Description
Inductive proximity sensor with M30*1.5 thread, PNP type output, manufacturer direct sale. This M30 proximity sensor is an IP67 rated inductive proximity sensor for detecting magnetic metal objects.
Functions
- Red LED checks the state of proximity sensor
- High repeated positioning accuracy
- High switching frequency
- Wide voltage range
- Antivibration, dust, water and oil prevention
- Reverse power protection, short circuit protection, directly connecting with PLC
- Can replace small switches and limit switches
Specification
| Model | ATO-PSI-30A10ZP | |||
| Installation type | Shielded | Unshielded | ||
| All the output methods | DC type | NPN | NO | NO |
| NC | NC | |||
| NO+NC | NO+NC | |||
| PNP | NO | NO | ||
| NC | NC | |||
| NO+NC | NO+NC | |||
| 2 wire | NO | NO | ||
| NC | NC | |||
| AC type | 2 wire | NO | NO | |
| NC | NC | |||
| 3 wire | NO+NC | NO+NC | ||
| Detection range | 10mm±10% | 15mm±10% | ||
| Setting distance | 0-8mm | 0-13mm | ||
| Delay distance | ≤10% detection range | |||
| Detection object | Magnetic metal (the detection distance decreases when it is non-magnetic metal) | |||
| Standard detection object | Iron 30*30*1mm | Iron 54*54*1mm | ||
| Response frequency | DC: 0.5kHz, AC: 50Hz | |||
| Supply voltage | DC type: DC 12-24V (6-36V), impulse (p-p) 10% below; AC type: AC 110-220V (90-250V) 50/60Hz | |||
| Withstand voltage | AC1000V 50/60Hz 1min between charging part and housing | |||
| Voltage influence | Inside ±15% rated supply voltage range, at rated supply voltage value, inside ±10% detection distance | |||
| Consumption current | N/P type: ≤13mA, D type: ≤0.8mA, A type: ≤1.7mA | |||
| Control output | N/P type: ≤300mA, D type: ≤200mA, A type: ≤400mA | |||
| Loop protection | N/P/D type: reversal connection protection, surge absorption, load short-circuit protection, A type: surge absorption | |||
| Ambient temperature & humidity | Operation temperature/storage temperature: -30~65℃ (no freeze, no dew); Operation humidity/storage humidity: 35~95%RH | |||
| Temperature influence | Temperature range -30~65℃, at +23℃, ±15% detection distance; Temperature range -25~60℃, at +23℃, ±10% detection distance | |||
| Insulation impedance | ≥50MΩ (DC500 megameter) between charging part and housing | |||
| Material | Housing: Nickel plated brass, Detection surface: ABS | |||
| Protection class | IP67 | |||
| Cable length | 1.2m |
Dimensional drawing (unit: mm)
Wiring diagram
Tips: Proximity sensor’s common problems on detect distance
- Proximity sensor can’t detect the distance of detected object.
- Sensor is installed within the detection range with unstable signal in the actual detection (sometimes detectable and sometimes undetectable).
- Actual detection distance is different from the standard detection distance indicated in sensor (or less than the detection distance, or larger than the detection distance).
Since there is a certain tolerance detection distance in proximity sensor that is 10% of the standard detection distance, that is to say, the detected object installed at the maximum distance could be influenced by its material so that the perception of sensor is at the critical point, causing the object sometime detectable and sometimes not. In addition, some industrial equipment or detected object has certain distance deviation in the process of operation or swinging. If a detected object is installed at the maximum detection distance, there could be a malfunction or bad reception.
Reviews
There are no reviews yet.